Results 1 to 8 of 8

Thread: Controlling Stepper from 3-1/2 floppy drive

  1. #1

    Default Controlling Stepper from 3-1/2 floppy drive

    Hi all!

    This is my first post here. Let me tell you about my project first. I am building a robotic eye which is a combination of
    motion detection and motion control. This "eye" is supposed
    to follow the moving object in the background (single moving
    object to oversimplify the things)

    I am very new to this. After a lots of research and reading,
    I decided to take out the stepper motor from the floppy drive.
    But it was a little different from the ones that I had read
    about. The motors I read about had 5 wires (1 common and other
    4 for the 4 half coil). This motor has only 4 of them. The
    floppy drive is from sony. I am bit confused regarding this.
    Is the body of the motor the common ground? The circuit I am
    following is here:
    http://www.doc.ic.ac.uk/~ih/doc/step...2/connect.html

    I am doing this for the first time. Any help as to where the
    fifth wire is?

    Regards
    --Himanshu

  2. #2
    Senior Member Cyborg devpriya's Avatar
    Join Date
    Jul 2005
    Location
    Seattle, WA, USA
    Posts
    275

    Default

    Hey if your motor has 4 wires then it must be a bi-polar one. Just search the net for "bipolar stepper motors" and you will get many circuits and sequences and answers to all your other queries.

  3. #3

    Default

    Mainly steppers are of 4,5,6 leads

    4- only bipolar stepper
    5- only unipolar stepper
    6- both unipolar as well as bipolar.

    So your's is bidirectional. Use L297 + L298 to drive that stepper motor. Bipolar steppers have good torque


    Bibin John
    www.bibinjohn.tk

  4. #4

    Default

    Hi!

    Thanks! I found another circuit without much effort.
    http://www.doc.ic.ac.uk/~ih/doc/step...r/flpystpr.txt

    The tiny stepper motor I took out from the drive hasn't any current
    ratings on it? Do these motors have standard current requirements.
    If so, what should be the current ratin for this one?

    Regards
    --Himanshu

  5. #5
    Member Android
    Join Date
    Sep 2004
    Location
    Mumbai
    Posts
    77

    Default

    the shaft of the floppy stepper does not stay porperly in place once you remove it from the drive. moreover those steppers are not powerful enough to turn a camera. buy a printer stepper from a scrap dealer, if ur frm mumbai pm me for the address.

  6. #6
    Member User
    Join Date
    Feb 2006
    Location
    God's own country
    Posts
    38

    Default Hello

    hello,

    I also doing a project in robotics. I saw a circuit using
    IC for controlling the stepper from a floppy drive in
    EFY magazine-April 2004.

  7. #7

    Default

    Hi!

    I am moving ahead with the circuit that I mentioned in the
    previous post!

    Thanks for your help!

    Regards
    --Himanshu
    Himanshu Chauhan
    System Software Engineer
    ===========================
    Good programmers know what to write
    Great one know what to rewrite
    --ESR
    ===========================

  8. #8

    Default stepper driver

    Hello sir,

    We are building a micromouse using stepper motors. We have 2 stepper motors with following ratings-
    1. 3.5V , 0.7A
    2. 3.8V , 0.67A

    The ratings of the two motors are different and we have to overdrive the motors at around 12V.
    For that purpose we are using IC SLA7024M (ALLEGRO MICROSYSTEMS) which is a PWM CHOPPER
    IC.
    So, we are facing certain difficulties,plzz help to sort them out.

    1. Can we overdrive the stepper motor of this rating at 12V?
    2. Which IC is better to use for driving it-IC SLA7024M or IC UCN5804B?
    3. If using IC SLA7024M , how the current through stepper motor is to be controlled?
    4. Will the different ratings of the two stepper motors affect the response much?

    thanxx a lott............

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •